R
ralli
Guest
Mein Umstieg von Debian zu freeBSD ist zwar erfolgreich gewesen, aber es gibt noch einige ungelöste Hardwareprobleme. Ich habe nach Lösungen gegoogelt, bin aber leider nicht fündig geworden, so das ich Eure Hilfe in Anpruch nehmen möchte.
Da meine Soundkarte (integrierter Chip auf Motherboard Sunshine (GA-8I915PM Ver 1.1)
7.1 Kanal Sound Realtek ALC880
nach folgendem Hinweis im Handbuch
The following and many other codecs have been verified to work:
Realtek ALC880
wohl nicht unterstützt wird, möchte ich wenigstens einige Soundtracks auf CD brennen, weil meine Minianlage mp3 abspielen kann.
Ich habe im PC folgenden Brenner eingebaut:
Philipps DVDR1628P1
Bus : ATA Device
Erkannt wird er auch:
dmesg ergibt:
Im Handbuch unter Kapitel 19.6 CDs benutzen steht doch:
19.6.3. burncd
Wenn Sie einen ATAPI-CD-Brenner besitzen, können Sie burncd benutzen, um ein ISO-Image auf CD zu brennen. burncd ist Teil des Basissystems und unter /usr/sbin/burncd installiert. Da es nicht viele Optionen hat, ist es leicht zu benutzen:
# burncd -f cddevice data imagefile.iso fixate
Dieses Kommando brennt eine Kopie von imagefile.iso auf das Gerät cddevice. In der Grundeinstellung wird das Gerät /dev/acd0 benutzt. burncd(8) beschreibt, wie die Schreibgeschwindigkeit gesetzt wird, die CD ausgeworfen wird und Audiodaten geschrieben werden.
burncd ist ja standardmäßig mitinstalliert.
Gebe ich jedoch auf der Konsole
ein, so wird auf cdrecord verwiesen:
burncd:
ATA_CAM option is enabled in kernel.
Install the sysutils/cdrtools port and use cdrecord instead.
Please refer to:
http://www.freebsd.org/doc/handbook/creating-cds.html#CDRECORD
Also habe ich mit pkg_add -r die cdrtools nachinstalliert.
Wenn ich
eingebe, um mein Brenner Device zu ermitteln kommt folgende Meldung:
Cdrecord-ProDVD-ProBD-Clone 3.00 (i386-unknown-freebsd9.0) Copyright (C) 1995-2010 Jörg Schilling
cdrecord: Inappropriate ioctl for device. CAMIOCOMMAND ioctl failed. Cannot open or use SCSI driver.
cdrecord: For possible targets try 'cdrecord -scanbus'.
cdrecord: For possible transport specifiers try 'cdrecord dev=help'.
Jetzt bin ich ratlos und weiss nicht weiter.
Da meine Soundkarte (integrierter Chip auf Motherboard Sunshine (GA-8I915PM Ver 1.1)
7.1 Kanal Sound Realtek ALC880
nach folgendem Hinweis im Handbuch
The following and many other codecs have been verified to work:
Realtek ALC880
wohl nicht unterstützt wird, möchte ich wenigstens einige Soundtracks auf CD brennen, weil meine Minianlage mp3 abspielen kann.
Ich habe im PC folgenden Brenner eingebaut:
Philipps DVDR1628P1
Bus : ATA Device
Erkannt wird er auch:
dmesg ergibt:
Code:
Copyright (c) 1992-2012 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 9.0-RELEASE #0: Tue Jan 3 07:15:25 UTC 2012
root@obrian.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC i386
CPU: Intel(R) Pentium(R) 4 CPU 3.00GHz (2992.56-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0xf43 Family = f Model = 4 Stepping = 3
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0x649d<SSE3,DTES64,MON,DS_CPL,EST,CNXT-ID,CX16,xTPR>
AMD Features=0x20100000<NX,LM>
TSC: P-state invariant
real memory = 2147483648 (2048 MB)
avail memory = 2073853952 (1977 MB)
Event timer "LAPIC" quality 400
ACPI APIC Table: <GBT AWRDACPI>
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
FreeBSD/SMP: 1 package(s) x 1 core(s) x 2 HTT threads
cpu0 (BSP): APIC ID: 0
cpu1 (AP/HT): APIC ID: 1
ioapic0: Changing APIC ID to 2
ioapic0 <Version 2.0> irqs 0-23 on motherboard
kbd1 at kbdmux0
acpi0: <GBT AWRDACPI> on motherboard
acpi0: Power Button (fixed)
acpi0: reservation of 0, a0000 (3) failed
acpi0: reservation of 100000, 7fef0000 (3) failed
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <PCI-PCI bridge> irq 16 at device 1.0 on pci0
pci1: <PCI bus> on pcib1
vgapci0: <VGA-compatible display> port 0x9000-0x907f mem 0xe2000000-0xe2ffffff,0xd0000000-0xdfffffff,0xe0000000-0xe1ffffff irq 16 at device 0.0 on pci1
nvidia0: <GeForce 9500 GT> on vgapci0
vgapci0: child nvidia0 requested pci_enable_io
vgapci0: child nvidia0 requested pci_enable_io
hdac0: <Intel 82801F High Definition Audio Controller> mem 0xf0100000-0xf0103fff irq 16 at device 27.0 on pci0
uhci0: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-A> port 0xbc00-0xbc1f irq 23 at device 29.0 on pci0
usbus0: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-A> on uhci0
uhci1: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-B> port 0xb000-0xb01f irq 19 at device 29.1 on pci0
usbus1: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-B> on uhci1
uhci2: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-C> port 0xb400-0xb41f irq 18 at device 29.2 on pci0
usbus2: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-C> on uhci2
uhci3: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-D> port 0xb800-0xb81f irq 16 at device 29.3 on pci0
usbus3: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-D> on uhci3
ehci0: <Intel 82801FB (ICH6) USB 2.0 controller> mem 0xf0104000-0xf01043ff irq 23 at device 29.7 on pci0
usbus4: EHCI version 1.0
usbus4: <Intel 82801FB (ICH6) USB 2.0 controller> on ehci0
pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci2: <ACPI PCI bus> on pcib2
pci2: <multimedia> at device 1.0 (no driver attached)
rl0: <RealTek 8139 10/100BaseTX> port 0xa000-0xa0ff mem 0xf0004000-0xf00040ff irq 21 at device 5.0 on pci2
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> PHY 0 on miibus0
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
rl0: Ethernet address: 00:14:85:44:88:e1
fwohci0: <Texas Instruments TSB43AB23> mem 0xf0005000-0xf00057ff,0xf0000000-0xf0003fff irq 23 at device 7.0 on pci2
fwohci0: OHCI version 1.10 (ROM=1)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:14:85:00:00:40:d5:2f
fwohci0: Phy 1394a available S400, 3 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
dcons_crom0: <dcons configuration ROM> on firewire0
dcons_crom0: bus_addr 0x20cc000
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:14:85:40:d5:2f
fwe0: Ethernet address: 02:14:85:40:d5:2f
fwip0: <IP over FireWire> on firewire0
fwip0: Firewire address: 00:14:85:00:00:40:d5:2f @ 0xfffe00000000, S400, maxrec 2048
fwohci0: Initiate bus reset
fwohci0: fwohci_intr_core: BUS reset
fwohci0: fwohci_intr_core: node_id=0x00000000, SelfID Count=1, CYCLEMASTER mode
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH6 SATA150 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xf000-0xf00f at device 31.2 on pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
attimer0: <AT timer> port 0x40-0x43 irq 0 on acpi0
Timecounter "i8254" frequency 1193182 Hz quality 0
Event timer "i8254" frequency 1193182 Hz quality 100
atrtc0: <AT realtime clock> port 0x70-0x73 irq 8 on acpi0
Event timer "RTC" frequency 32768 Hz quality 0
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0
ppc0: <Parallel port> port 0x378-0x37f,0x778-0x77b irq 7 drq 3 on acpi0
ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/16 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem 0xc0000-0xcdfff,0xd0000-0xd7fff,0xd8000-0xd8fff pnpid ORM0000 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
acpi_perf0: <ACPI CPU Frequency Control> on cpu0
p4tcc0: <CPU Frequency Thermal Control> on cpu0
est1: <Enhanced SpeedStep Frequency Control> on cpu1
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr f2d00000f2d
device_attach: est1 attach returned 6
p4tcc1: <CPU Frequency Thermal Control> on cpu1
Timecounters tick every 1.000 msec
firewire0: 1 nodes, maxhop <= 0 cable IRM irm(0) (me)
firewire0: bus manager 0
hdac0: HDA Codec #2: Realtek ALC880
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 12Mbps Full Speed USB v1.0
usbus3: 12Mbps Full Speed USB v1.0
usbus4: 480Mbps High Speed USB v2.0
ugen0.1: <Intel> at usbus0
uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ugen1.1: <Intel> at usbus1
uhub1: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
ugen2.1: <Intel> at usbus2
uhub2: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2
ugen3.1: <Intel> at usbus3
uhub3: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
ugen4.1: <Intel> at usbus4
uhub4: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus4
uhub0: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
uhub2: 2 ports with 2 removable, self powered
uhub3: 2 ports with 2 removable, self powered
ada0 at ata0 bus 0 scbus0 target 0 lun 0
ada0: <ST3250823AS 3.03> ATA-7 SATA 1.x device
ada0: 150.000MB/s transfers (SATA, UDMA5, PIO 8192bytes)
ada0: 238475MB (488397168 512 byte sectors: 16H 63S/T 16383C)
ada0: Previously was known as ad0
cd0 at ata1 bus 0 scbus1 target 0 lun 0
cd0: <HL-DT-ST DVD-ROM GDR8163B 0N21> Removable CD-ROM SCSI-0 device
cd0: 66.700MB/s transfers (UDMA4, ATAPI 12bytes, PIO 65534bytes)
cd0: Attempt to query device size failed: NOT READY, Medium not present
cd1 at ata1 bus 0 scbus1 target 1 lun 0
cd1: <PHILIPS DVDR1628P1 Q1.1> Removable CD-ROM SCSI-0 device
cd1: 33.300MB/s transfers (UDMA2, ATAPI 12bytes, PIO 65534bytes)
cd1: Attempt to query device size failed: NOT READY, Medium not present
SMP: AP CPU #1 Launched!
Timecounter "TSC-low" frequency 11689684 Hz quality 1000
Root mount waiting for: usbus4
Root mount waiting for: usbus4
uhub4: 8 ports with 8 removable, self powered
Root mount waiting for: usbus4
Trying to mount root from ufs:/dev/ada0p2 [rw]...
ugen2.2: <Logitech> at usbus2
ums0: <Logitech USB Optical Mouse, class 0/0, rev 2.00/43.01, addr 2> on usbus2
ums0: 3 buttons and [XYZ] coordinates ID=0
ugen3.2: <vendor 0x0451> at usbus3
uhub5: <vendor 0x0451 product 0x1446, class 9/0, rev 1.10/1.10, addr 2> on usbus3
uhub5: 4 ports with 4 removable, bus powered
Im Handbuch unter Kapitel 19.6 CDs benutzen steht doch:
19.6.3. burncd
Wenn Sie einen ATAPI-CD-Brenner besitzen, können Sie burncd benutzen, um ein ISO-Image auf CD zu brennen. burncd ist Teil des Basissystems und unter /usr/sbin/burncd installiert. Da es nicht viele Optionen hat, ist es leicht zu benutzen:
# burncd -f cddevice data imagefile.iso fixate
Dieses Kommando brennt eine Kopie von imagefile.iso auf das Gerät cddevice. In der Grundeinstellung wird das Gerät /dev/acd0 benutzt. burncd(8) beschreibt, wie die Schreibgeschwindigkeit gesetzt wird, die CD ausgeworfen wird und Audiodaten geschrieben werden.
burncd ist ja standardmäßig mitinstalliert.
Gebe ich jedoch auf der Konsole
Code:
burncd
burncd:
ATA_CAM option is enabled in kernel.
Install the sysutils/cdrtools port and use cdrecord instead.
Please refer to:
http://www.freebsd.org/doc/handbook/creating-cds.html#CDRECORD
Also habe ich mit pkg_add -r die cdrtools nachinstalliert.
Wenn ich
Code:
cdrecord -scanbus
eingebe, um mein Brenner Device zu ermitteln kommt folgende Meldung:
Cdrecord-ProDVD-ProBD-Clone 3.00 (i386-unknown-freebsd9.0) Copyright (C) 1995-2010 Jörg Schilling
cdrecord: Inappropriate ioctl for device. CAMIOCOMMAND ioctl failed. Cannot open or use SCSI driver.
cdrecord: For possible targets try 'cdrecord -scanbus'.
cdrecord: For possible transport specifiers try 'cdrecord dev=help'.
Jetzt bin ich ratlos und weiss nicht weiter.